-
Auxiliary Equipment
-
-
Contact
EXTRUSION LINES
PRODUCTION, AND SALES OF CAST FILM, STRETCH FILM, SHEET, AND PLATE EXTRUSION EQUIPMENT
integrated dehumidification dryer
Classification：
Keyword：
Overview Introduction
The dehumidification dryer should be aimed at engineering plastics with strong hygroscopicity to solve the bad quality problems such as bubbles, crazes, corner cracks, flow marks and poor transparency caused by the products not being dried well; Engineering plastics such as PA, PC, PBT, PET, NYLOM and other materials with strong hygroscopicity infiltrate into the plastic granules from dry water, which cannot be completely dried by traditional dryers.
E-mail: jack.zhang@5emachine.com
Phone / WhatsApp: +86-137-1228-0099
Message InquiryPRODUCT DETAILS INTRODUCTION
Use of Dehumidifying dryer:
● The dehumidification dryer should be aimed at engineering plastics with strong hygroscopicity to solve the bad quality problems such as bubbles, crazes, corner cracks, flow marks and poor transparency caused by the products not being dried well; Engineering plastics such as PA, PC, PBT, PET, NYLOM and other materials with strong hygroscopicity infiltrate into the plastic granules from dry water, which cannot be completely dried by traditional dryers.
● The dehumidification dryer is mainly used with the hot air hopper dryer for efficient dehumidification and drying.
● It has been proved by practice that only by reducing the dew point of the drying air to below - 40 ℃ and controlling the heat to blow it over the surface of the wet plastic particles can the moisture content of the drying air be reduced to below 0.02% before molding.
● Honeycomb dehumidifier is to fully dehumidify the air in a closed circulating system, and rapidly separate the water in the plastic particles to achieve the effect of dehumidification in the dry
Operating principle of Dehumidifying dryer:
● In the process of raw material treatment, the dehumidification dryer uses the honeycomb runner with strong dehumidification performance. After the water in the blank is collected. The air with low dew point and strong moisture absorption capacity is formed for dehumidification and drying of raw materials.
● Therefore, the dry air provided can easily reach a dew point of - 32~40 degrees, or even below - 40 degrees under ideal conditions. The temperature of the visual dew point is stable, ensuring the quality and stability of the molded plastic products. The whole series adopts P.I.D temperature control system standard equipment; The maximum dry air volume of the product can reach 3000 m3/h with LED LCD
Features of Dehumidifying dryer:
● The P.I.D temperature control system is adopted, which has regeneration temperature setting and actual temperature display screens.
● The rotation speed of the honeycomb wheel can be adjusted.
● Double condenser structure is adopted to ensure lower return air temperature and dew point.
● Honeycomb can reach dew point below - 40 ℃, and even lower than - 50 ℃ under enhanced configuration
● PLC control and LCD touch human-computer interface are optional.
● Dew point meter that can monitor the dehumidification effect of the machine at any time is optional.
● The machine occupies a small area and is easy to move. The machine can be replaced at will.
Technical parameters of dehumidifying dryer (single type):
|
model |
Airflow rate for drying(m3/hr) |
Drying Fan Power(Kw) |
Renewable Wind Turbine Capacity(Kw) |
Regenerative heating power(Kw) |
Inlet/outlet diameter(Inch) |
Dimensions(cm) |
Net weight (kg) |
|
5E-80H |
80 |
0.75 |
0.25 |
3.9 |
2〃 |
128X55X82 |
120 |
|
5E-130H |
130 |
1.1 |
0.25 |
3.9 |
2〃 |
128X55X82 |
140 |
|
5E-160H |
160 |
1.5 |
0.55 |
5.4 |
2.5〃 |
153X66X105 |
215 |
|
5E-220H |
220 |
2.2 |
0.55 |
5.4 |
2.5〃 |
153X66X105 |
225 |
|
5E-300H |
300 |
3 |
0.75 |
7.2 |
3〃 |
170X70X126 |
240 |
|
5E-400H |
400 |
5.5 |
0.75 |
7.2 |
3〃 |
170X70X126 |
280 |
|
5E-500H |
500 |
5.5 |
2.2 |
10 |
4〃 |
180X90X130 |
290 |
|
5E-700H |
700 |
7.5 |
2.2 |
10 |
4〃 |
180X90X130 |
300 |
PRODUCT DETAILS DISPLAY
COMPANY CULTURE
PRODUCTION, AND SALES OF CAST FILM, STRETCH FILM, SHEET, AND PLATE EXTRUSION EQUIPMENT
Easy to Install
Modular structure, reasonable layout, simple on-site connection, greatly shortening installation period, reducing difficulty and labor cost.
Easy to Debug
Clear and intuitive parameter interface, optimized preset process, simplified debugging steps, easy for new operators to quickly start stable production.
Easy to Operate
Humanized touch control, simple logic, one-key function switching, lower requirement for professional skills, easy and efficient operation.
Easy to Maintain
Open layout for key components, easy replacement of wearing parts, clear maintenance guidance, simple daily care, less downtime and lower cost.
Easy Upgrade
Reserved expansion interfaces for hardware, online update supported for software, flexible upgrade according to process and capacity needs, extending equipment life.
FREQUENTLY ASKED QUESTIONS
What are the regular maintenance tasks for the website?
Regular website maintenance is key to ensuring website security, stable operation, and user experience. Maintenance work includes updating website content, checking and fixing website links, backing up data, conducting regular security checks, fixing vulnerabilities, optimizing performance, etc. These tasks help ensure the long-term effective operation of the website and provide a good user experience.
What is the difference between UI and UX in website design?
UI (user interface) and UX (user experience) are two important aspects in website design. UI focuses on the appearance design, layout, and visual elements of a website, while UX emphasizes the overall user experience and interaction on the website, including usability, navigation, interaction, and more. Excellent UI design typically enhances the user experience.
